Watch the Preparation Demonstration
Watch how the pipette and burette are prepared for titration, then use the steps below to explain why each is rinsed with distilled water followed by the solution it will contain.
Watch on YouTube (opens in a new tab)
Objective:
To rinse both apparatus with water followed by the chemical solution which they should contain.
Pipette Preparation:
Labels and filler type: Solution Q is the label used in this example. In your own practical, use the solution specified for the pipette. The A/S/E controls described here apply to a three-valve bulb filler; follow your filler’s instructions if its design is different.
- Prepare a Waste Beaker
Point the tip of the pipette into the waste beaker and rinse it with distilled water. Rotate the pipette as you rinse to ensure all internal surfaces are covered. - Drain the Pipette
Allow the distilled water to flow out completely after rinsing. - Rinse with the Correct Solution
Read the instructions carefully. For this experiment, use Solution Q to rinse the pipette. - Attach the Pipette Filler
Hold the pipette near the top and gently insert it into the pipette filler. Avoid pushing too hard to prevent breakage. - Draw Solution into the Pipette
For a three-valve filler, press “A” while squeezing the bulb to expel air, then release “A”. Place the pipette tip into Solution Q and press “S” on the filler to draw the solution up. Fill the pipette about halfway for rinsing, keeping liquid out of the filler. - Rinse the Internal Walls
Remove the pipette filler, then hold the pipette horizontally over the waste beaker and rotate it so the solution coats all internal surfaces. - Discard the Solution
Allow the rinse solution to drain into the waste beaker with the filler removed. Alternatively, gently reattach the three-valve filler, hold the pipette upright, and press “E” to release the rinse solution. - Complete the Rinsing Process
Once the rinse solution has drained, place the pipette back on the stand. It is now conditioned and ready for accurate filling to measure the volume specified in the titration experiment.
Burette Preparation
- Ensure the Stopcock Is Closed
Before adding any liquid, make sure the stopcock is fully closed to prevent leakage. - Add Distilled Water
Place a filter funnel at the top and, for this example, fill about one-third of the burette with distilled water. Remove the funnel after filling. - Rinse the Internal Walls
Open the stopcock to allow some water to flow through. Close the stopcock again before holding the burette horizontally and rotating it so the distilled water contacts all internal surfaces. - Discard the Distilled Water
Empty all the water from the burette. Remember to also drain the liquid from the tip by opening the stopcock. - Rinse with the Correct Solution
Repeat the rinsing process using the solution required for the experiment (for this case, Solution R). Ensure the stopcock is closed before filling. - Fill and Rinse Again
Use a funnel to add a small portion of Solution R for rinsing. Remove the funnel, then rotate the burette to coat all internal surfaces. Keep the stopcock closed while doing this. - Discard the Solution
Empty all the rinse solution, including any liquid in the tip, into a waste beaker by opening the stopcock. Repeat with fresh small portions as instructed, then close the stopcock. - Final Setup
Place the burette back onto the stand and clamp it vertically. It is now rinsed and conditioned, ready for filling before use in titration.
Final Check
Final Check: Both the pipette and burette are now rinsed and conditioned with their assigned solutions: Solution Q for the pipette and Solution R for the burette in this example. They still need to be filled and set for measurement before titration.
Both pipette and burette are now conditioned for use in titration. For the actual transfer, use the filler to set Solution Q to the pipette’s calibration mark, then follow the pipette’s delivery instructions.
Before measuring with the burette: Fill the vertically clamped burette with Solution R. Remove the funnel and run a little solution through the tap until the tip is filled and any air bubbles are cleared. Close the stopcock, allow the level to settle, and record the initial meniscus reading at eye level. It does not need to start at zero.
Sources and Related Reading
Written apparatus technique checked on 2 November 2026. Follow the instructions for your actual pipette filler, glassware and practical. Solution Q and Solution R are the labels used in this example.
References
Start Your Chemistry Tuition Journey With Achievers Dream
At Achievers Dream, we offer specialised Primary Science Tuition, O Level Chemistry Tuition, Lower Secondary Science Tuition and JC Chemistry tuition. Our teaching team includes former MOE Heads of Department, NIE-trained teachers and full-time tutors.
As a tuition centre in Singapore, students will be provided with a wide range of information from sources such as exclusive cheat sheets, sec 1 science notes, science revision guides or other supplementary/topic by topic notes.
Join Our Exclusive Telegram Group Here
Click Here for Free Access to our coloured Chemistry notes
We provide structured lessons with personalised support, alongside facilities such as our chemistry laboratory and a student portal. Our team will be there for you to support your learning journey, start now and achieve better results
